Enfield Envoy 7.62 x 51 Bolt Action Rifle
Enfield Envoy 7.62 x 51 Bolt Action Rifle
Enfield Envoy 7.62 x 51 Bolt Action Rifle. The L42A1 is a bolt-action sniper rifle chambered for the 7.62×51mm NATO cartridge. Used in the past by the British Army, Royal Marines and Royal Air Force RAF Regiment, the L42A1 entered service in 1970. It was replaced by the Accuracy International AW (as the L96A1) in 1985.
The L42A1 has been used in several conflicts, including the Dhofar Rebellion in Oman,[5] The Troubles in Northern Ireland, the Falklands War, and the Gulf War.
The L42A1 was the last model in a long line of bolt-action rifles that used a rear-locking action designed by James Paris Lee for the British Army. This action design appeared first in the Lee–Metford rifle of 1888.
The Enfield Envoy is similar to the L39A1, but was produced with a higher standard of external finish for sale on the civilian market. It had a fore-end of broader cross section of the same shape as the No.8, and was supplied with a No.8 style butt.
This rifle is in superb condition and is fitted with an Alfred J Parker TZ 4/47 aperture sight and a Parker Hale tunnel foresight. These are very rare rifles and were only produced in very limited numbers.
** Ammunition, Firearms and any Licensed components are not available to order online. Due to current Firearms Legislation these items are collection only and can only be purchased upon production of the necessary Firearms Permits. If you would like to purchase this item then please contact us on info@guntopia.hu or call +36 30 304 3036 **
| Barrel | |
|---|---|
| Calibre | |
| Manufacturer |
565 950 Ft
Enfield Envoy 7.62 x 51 Bolt Action Rifle
The L42A1 was a 7.62×51mm NATO conversion of the Second World War era .303 British chambered Lee–Enfield Rifle No. 4 Mk1(T) and No. 4 Mk1*(T), which had remained in service for some time after the 7.62×51mm NATO L1A1 Self-Loading Rifle replaced the Rifle No.4 as the standard service rifle in 1957. It differed from other post-war No. 4 based variants in that the trigger remained hinged on the trigger guard as on the No.4 Mk1 and 1*, not hung from the receiver as in the later No. 4 Mk 2, Mk 1/2 and Mk 1/3 .303 British rifles, and other 7.62×51mm NATO conversions.
The conversion programme was carried out at Royal Small Arms Factory Enfield from 1970 to 1971 and about 1,080 rifles were converted. A new hammer-forged heavy 7.62×51mm NATO barrel was installed, with four-groove, right hand twist rifling instead of the five-groove left-hand Enfield-type rifling used in .303 British barrels. The heavier barrel was free-floating, which meant that the required accuracy standard could be achieved without the barrel bearing against the wooden fore-end, as had been the case with the No.4 MkI(T). Therefore, the woodwork was modified by shortening the fore-end to 1/2" in front of the middle band, and a new design for an upper handguard was fitted.
A new magazine suitable for the 7.62×51mm NATO cartridge was attached; it is recognizable by its more square shape when compared against the .303 British version. A hardened projection of the left magazine lip serves as an ejector, although the .303 British ejector screw remained in place. The butt with its screwed-on cheekpiece was retained, however the scope number on the wrist of the stock, was obliterated with "X"-outs, and new numbers applied. The markings on the left side of the receiver were obliterated and new markings reflecting the new rifle's designation and chambering were applied. The original markings are sometimes partially visible underneath.
Additional information
| Barrel | |
|---|---|
| Calibre | |
| Manufacturer |
